Eaton FP1007R1-R30-R 300 nH Power Inductor, 60 A
Eaton FP1007R1-R30-R 300 nH Power Inductor, 60 A

Eaton FP1007R1-R30-R 300 nH Power Inductor, 60 A

Share
pEaton FP1007R1-R30-R: 300 nH high frequency, high current power inductor, 60 A Irms, 32 A Isat, DCR 0.29 mOhm, 10.4 x 8.0 mm package./p
    • Product Details
    • Download

    FP1007R1-R30-R at a glance: 300 nH high frequency, high current power inductor, 60 A Irms, 32 A Isat, DCR 0.29 mOhm, 10.4 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1007R1-R30-R High frequency, high current power inductors

    FP1007R1-R30-R is one of Eaton's high frequency, high current power inductor series, 10.4 x 8.0 mm with a 7.5 mm tall profile. Electrically it offers 300 nH at 60 A Irms and 0.29 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Key Specifications

    Orderable part numberFP1007R1-R30-R
    Inductance, OCL (0 Adc)300 nH
    Inductance, FLL (minimum)216 nH
    Irms (40 °C rise, no core loss)60 A
    Isat (20% roll-off @ +25 °C)32 A
    Isat2 (20% roll-off @ +125 °C)26 A
    DCR typical @ +20 °C0.29 mOhm
    K-factor (Bp-p = K x L x dI)371
    Package10.4 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    300 nH open-circuit, 216 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 32 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 1044 mW (60 A squared times 0.29 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 371 and a ripple of 9.6 A the core sees roughly 106.8 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    The 10.4 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 300 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 15 of 17 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.29 mOhm.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Size the inductor on peak current first, not average. With 300 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.29 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1007R1-R30-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products