Eaton FP1007R2-R14-R High Current Inductor, 140 nH 0.48 mOhm
Eaton FP1007R2-R14-R High Current Inductor, 140 nH 0.48 mOhm

Eaton FP1007R2-R14-R High Current Inductor, 140 nH 0.48 mOhm

Share
pEaton FP1007R2-R14-R: 140 nH high frequency, high current power inductor, 51 A Irms, 72 A Isat, DCR 0.48 mOhm, 10.4 x 8.0 mm package./p
    • Product Details
    • Download

    FP1007R2-R14-R at a glance: 140 nH high frequency, high current power inductor, 51 A Irms, 72 A Isat, DCR 0.48 mOhm, 10.4 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1007R2-R14-R High frequency, high current power inductors

    Eaton FP1007R2-R14-R is a high frequency, high current power inductor in a 10.4 x 8.0 mm surface-mount package. It carries 140 nH of open-circuit inductance with 51 A Irms and a typical DCR of 0.48 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 7.5 mm tall and rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1007R2-R14-R
    Inductance, OCL (0 Adc)140 nH
    Inductance, FLL (minimum)100 nH
    Irms (40 °C rise, no core loss)51 A
    Isat (20% roll-off @ +25 °C)72 A
    Isat2 (20% roll-off @ +125 °C)56 A
    DCR typical @ +20 °C0.48 mOhm
    K-factor (Bp-p = K x L x dI)368
    Package10.4 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two inductance figures are published. 140 nH is measured with no DC in the winding, 100 nH with the winding loaded to Isat1. The gap between them is 29%, and it is the reason a converter that looks well damped at no load can ring at full current.

    The first Isat column, 72 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 1248 mW dissipated at 51 A through 0.48 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 368 and a ripple of 21.6 A the core sees roughly 111.3 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Where This Part Sits in the Range

    The 10.4 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 140 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 17 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.48 mOhm, which is what the extra turns cost, Irms of 51 A is the bottom of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 140 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.48 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1007R2-R14-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products