
FP1007R2-R22-R at a glance: 215 nH high frequency, high current power inductor, 51 A Irms, 50 A Isat, DCR 0.48 mOhm, 10.4 x 8.0 mm body, 7.5 mm tall.
The FP1007R2-R22-R is a 10.4 x 8.0 mm high frequency, high current power inductor from Eaton, rated 51 A Irms at 215 nH and 0.48 mOhm typical DCR. It is a surface-mount part 7.5 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.
| Orderable part number | FP1007R2-R22-R |
| Inductance, OCL (0 Adc) | 215 nH |
| Inductance, FLL (minimum) | 155 nH |
| Irms (40 °C rise, no core loss) | 51 A |
| Isat (20% roll-off @ +25 °C) | 50 A |
| Isat2 (20% roll-off @ +125 °C) | 36 A |
| DCR typical @ +20 °C | 0.48 mOhm |
| K-factor (Bp-p = K x L x dI) | 368 |
| Package | 10.4 x 8.0 mm, 7.5 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 215 nH. Put Isat1 through it and the figure falls to 155 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 215 nH number; loop stability and worst-case current belong on the lower one.
Peak current at 20% roll-off is 50 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
The 1248 mW dissipated at 51 A through 0.48 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
The K-factor of 368 turns ripple into flux: a peak-to-peak swing of 15 A gives about 118.7 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.
The 10.4 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 215 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 10 of 17 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.48 mOhm, which is what the extra turns cost, Irms of 51 A is the bottom of the family.
The order of checks that works: compute ripple from 215 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.48 mOhm the winding is not the loss, the trace can be.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Can I substitute a lower inductance in the same body?
Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd