Eaton FP1007R3-R30-R 300 nH 35 A Saturation Inductor
Eaton FP1007R3-R30-R 300 nH 35 A Saturation Inductor

Eaton FP1007R3-R30-R 300 nH 35 A Saturation Inductor

Share
pEaton FP1007R3-R30-R: 300 nH high frequency, high current power inductor, 61 A Irms, 35 A Isat, DCR 0.29 mOhm, 10.4 x 8.0 mm package./p
    • Product Details
    • Download

    FP1007R3-R30-R at a glance: 300 nH high frequency, high current power inductor, 61 A Irms, 35 A Isat, DCR 0.29 mOhm, 10.4 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1007R3-R30-R High frequency, high current power inductors

    Eaton builds the FP1007R3-R30-R as a high frequency, high current power inductor for 10.4 x 8.0 mm footprints. At 300 nH and 61 A Irms with 0.29 mOhm of DCR it targets high-current DC-DC stages; the 7.5 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1007R3-R30-R
    Inductance, OCL (0 Adc)300 nH
    Inductance, FLL (minimum)216 nH
    Irms (40 °C rise, no core loss)61 A
    Isat (20% roll-off @ +25 °C)35 A
    Isat2 (20% roll-off @ +125 °C)30 A
    DCR typical @ +20 °C0.29 mOhm
    K-factor (Bp-p = K x L x dI)354
    Package10.4 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    300 nH open-circuit, 216 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 35 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 1079 mW (61 A squared times 0.29 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 111.5 mT for a 10.5 A ripple (K = 354). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    The 10.4 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 300 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 15 of 17 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.29 mOhm, Irms of 61 A is the top of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Size the inductor on peak current first, not average. With 300 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.29 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1007R3-R30-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products