Eaton FP1007R6-R22-R High Current Inductor, 220 nH 0.29 mOhm
Eaton FP1007R6-R22-R High Current Inductor, 220 nH 0.29 mOhm

Eaton FP1007R6-R22-R High Current Inductor, 220 nH 0.29 mOhm

Share
pEaton FP1007R6-R22-R: 220 nH high frequency, high current power inductor, 61 A Irms, 50 A Isat, DCR 0.29 mOhm, 10.5 x 8.0 mm package./p
    • Product Details
    • Download

    FP1007R6-R22-R at a glance: 220 nH high frequency, high current power inductor, 61 A Irms, 50 A Isat, DCR 0.29 mOhm, 10.5 x 8.0 mm body, 7.0 mm max tall.

    Eaton FP1007R6-R22-R High frequency, high current power inductors

    The FP1007R6-R22-R is a 10.5 x 8.0 mm high frequency, high current power inductor from Eaton, rated 61 A Irms at 220 nH and 0.29 mOhm typical DCR. It is a surface-mount part 7.0 mm max tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP1007R6-R22-R
    Inductance, OCL (0 Adc)220 nH
    Inductance, FLL (minimum)158 nH
    Irms (40 °C rise, no core loss)61 A
    Isat (20% roll-off @ +25 °C)50 A
    Isat2 (20% roll-off @ +100 °C)40 A
    DCR typical @ +20 °C0.29 mOhm
    K-factor (Bp-p = K x L x dI)348.8
    Package10.5 x 8.0 mm, 7.0 mm max height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 220 nH. Put Isat1 through it and the figure falls to 158 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 220 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 50 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 1079 mW (61 A squared times 0.29 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 348.8 turns ripple into flux: a peak-to-peak swing of 15 A gives about 115.1 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    The 10.5 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 220 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 3 of 7 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Size the inductor on peak current first, not average. With 220 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.29 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1007R6-R22-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products