
FP1007R6-R47-R at a glance: 470 nH high frequency, high current power inductor, 61 A Irms, 23.5 A Isat, DCR 0.29 mOhm, 10.5 x 8.0 mm body, 7.0 mm max tall.
Eaton builds the FP1007R6-R47-R as a high frequency, high current power inductor for 10.5 x 8.0 mm footprints. At 470 nH and 61 A Irms with 0.29 mOhm of DCR it targets high-current DC-DC stages; the 7.0 mm max tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.
| Orderable part number | FP1007R6-R47-R |
| Inductance, OCL (0 Adc) | 470 nH |
| Inductance, FLL (minimum) | 338 nH |
| Irms (40 °C rise, no core loss) | 61 A |
| Isat (20% roll-off @ +25 °C) | 23.5 A |
| Isat2 (20% roll-off @ +100 °C) | 19 A |
| DCR typical @ +20 °C | 0.29 mOhm |
| K-factor (Bp-p = K x L x dI) | 348.8 |
| Package | 10.5 x 8.0 mm, 7.0 mm max height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
470 nH open-circuit, 338 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.
Peak current at 20% roll-off is 23.5 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
The 1079 mW dissipated at 61 A through 0.29 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
Core loss needs flux, and flux here is about 115.6 mT for a 7.05 A ripple (K = 348.8). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
The 10.5 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 470 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.
That makes it the highest inductance of the 7 parts in this data sheet.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 470 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
On the board, place the part so the switch-node copper is short and wide. At 0.29 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd