Eaton FP1008L1-R150-R 65 A SMD Power Inductor, 150 nH
Eaton FP1008L1-R150-R 65 A SMD Power Inductor, 150 nH

Eaton FP1008L1-R150-R 65 A SMD Power Inductor, 150 nH

Share
pEaton FP1008L1-R150-R: 150 nH high frequency, high current power inductor, 65 A Irms, 50 A Isat, DCR 0.17 mOhm, 10.0 x 8.0 mm package./p
    • Product Details
    • Download

    FP1008L1-R150-R at a glance: 150 nH high frequency, high current power inductor, 65 A Irms, 50 A Isat, DCR 0.17 mOhm, 10.0 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1008L1-R150-R High frequency, high current power inductors

    FP1008L1-R150-R is one of Eaton's high frequency, high current power inductor series, 10.0 x 8.0 mm with a 8.0 mm tall profile. Electrically it offers 150 nH at 65 A Irms and 0.17 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Key Specifications

    Orderable part numberFP1008L1-R150-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)108 nH
    Irms (40 °C rise, no core loss)65 A
    Isat (20% roll-off @ +25 °C)50 A
    Isat2 (20% roll-off @ +100 °C)44 A
    Isat3 (20% roll-off @ +125 °C)42 A
    DCR typical @ +20 °C0.17 mOhm
    K-factor (Bp-p = K x L x dI)461
    Package10.0 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    150 nH open-circuit, 108 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 50 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 718 mW (65 A squared times 0.17 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 461 turns ripple into flux: a peak-to-peak swing of 15 A gives about 103.7 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    The 10.0 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 2 of 3 when the data sheet is sorted by inductance.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    The order of checks that works: compute ripple from 150 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.17 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1008L1-R150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message