Eaton FP1008R5-R180-R High Current Inductor, 180 nH 0.17 mOhm
Eaton FP1008R5-R180-R High Current Inductor, 180 nH 0.17 mOhm

Eaton FP1008R5-R180-R High Current Inductor, 180 nH 0.17 mOhm

Share
pEaton FP1008R5-R180-R: 180 nH high frequency, high current power inductor, 79 A Irms, 70 A Isat, DCR 0.17 mOhm, 10.8 x 8.0 mm package./p
    • Product Details
    • Download

    FP1008R5-R180-R at a glance: 180 nH high frequency, high current power inductor, 79 A Irms, 70 A Isat, DCR 0.17 mOhm, 10.8 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1008R5-R180-R High frequency, high current power inductors

    Eaton FP1008R5-R180-R is a high frequency, high current power inductor in a 10.8 x 8.0 mm surface-mount package. It carries 180 nH of open-circuit inductance with 79 A Irms and a typical DCR of 0.17 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 8.0 mm tall and rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1008R5-R180-R
    Inductance, OCL (0 Adc)180 nH
    Inductance, FLL (minimum)130 nH
    Irms (40 °C rise, no core loss)79 A
    Isat (20% roll-off @ +25 °C)70 A
    Isat2 (20% roll-off @ +100 °C)56 A
    Isat3 (20% roll-off @ +125 °C)53 A
    DCR typical @ +20 °C0.17 mOhm
    K-factor (Bp-p = K x L x dI)342
    Package10.8 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Two inductance figures are published. 180 nH is measured with no DC in the winding, 130 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    The first Isat column, 70 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 1061 mW dissipated at 79 A through 0.17 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 342 turns ripple into flux: a peak-to-peak swing of 21 A gives about 129.3 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    The 10.8 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 180 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 6 of 13 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.17 mOhm, Irms of 79 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Size the inductor on peak current first, not average. With 180 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.17 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1008R5-R180-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message