
FP1008R5-R220-R at a glance: 220 nH high frequency, high current power inductor, 79 A Irms, 58 A Isat, DCR 0.17 mOhm, 10.8 x 8.0 mm body, 8.0 mm tall.
FP1008R5-R220-R is one of Eaton's high frequency, high current power inductor series, 10.8 x 8.0 mm with a 8.0 mm tall profile. Electrically it offers 220 nH at 79 A Irms and 0.17 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP1008R5-R220-R |
| Inductance, OCL (0 Adc) | 220 nH |
| Inductance, FLL (minimum) | 158 nH |
| Irms (40 °C rise, no core loss) | 79 A |
| Isat (20% roll-off @ +25 °C) | 58 A |
| Isat2 (20% roll-off @ +100 °C) | 44 A |
| Isat3 (20% roll-off @ +125 °C) | 42 A |
| DCR typical @ +20 °C | 0.17 mOhm |
| K-factor (Bp-p = K x L x dI) | 342 |
| Package | 10.8 x 8.0 mm, 8.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 220 nH. Put Isat1 through it and the figure falls to 158 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 220 nH number; loop stability and worst-case current belong on the lower one.
Peak current at 20% roll-off is 58 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
Irms of 79 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.17 mOhm that is roughly 1061 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
Flux swing follows Bp-p = K x L x dI. With K = 342 and a ripple of 17.4 A the core sees roughly 130.9 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.
The 10.8 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 220 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 8 of 13 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.17 mOhm, Irms of 79 A is the top of the family.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 220 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.17 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Why does DCR have both a typical and a maximum figure?
The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.
What does the R suffix on the part number mean?
It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd