Eaton FP1008R6-R100-R - 100 nH Shielded Power Inductor 10.8 x 8.0 mm
Eaton FP1008R6-R100-R - 100 nH Shielded Power Inductor 10.8 x 8.0 mm

Eaton FP1008R6-R100-R - 100 nH Shielded Power Inductor 10.8 x 8.0 mm

Share
pEaton FP1008R6-R100-R: 100 nH high frequency, high current power inductor, 74 A Irms, 103 A Isat, DCR 0.18 mOhm, 10.8 x 8.0 mm package./p
    • Product Details
    • Download

    FP1008R6-R100-R at a glance: 100 nH high frequency, high current power inductor, 74 A Irms, 103 A Isat, DCR 0.18 mOhm, 10.8 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1008R6-R100-R High frequency, high current power inductors

    FP1008R6-R100-R is one of Eaton's high frequency, high current power inductor series, 10.8 x 8.0 mm with a 8.0 mm tall profile. Electrically it offers 100 nH at 74 A Irms and 0.18 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Ratings at a Glance

    Orderable part numberFP1008R6-R100-R
    Inductance, OCL (0 Adc)100 nH
    Inductance, FLL (minimum)72 nH
    Irms (40 °C rise, no core loss)74 A
    Isat (20% roll-off @ +25 °C)103 A
    Isat2 (20% roll-off @ +100 °C)86 A
    Isat3 (20% roll-off @ +125 °C)81 A
    DCR typical @ +20 °C0.18 mOhm
    K-factor (Bp-p = K x L x dI)342
    Package10.8 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two inductance figures are published. 100 nH is measured with no DC in the winding, 72 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 103 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 986 mW dissipated at 74 A through 0.18 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 342 and a ripple of 30.9 A the core sees roughly 105.7 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    The 10.8 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 13 parts in this data sheet, with the highest DCR in the series at 0.18 mOhm, which is what the extra turns cost, Irms of 74 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 100 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.18 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1008R6-R100-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message