Eaton FP1008R6-R150-R 74 A SMD Power Inductor, 150 nH
Eaton FP1008R6-R150-R 74 A SMD Power Inductor, 150 nH

Eaton FP1008R6-R150-R 74 A SMD Power Inductor, 150 nH

Share
pEaton FP1008R6-R150-R: 150 nH high frequency, high current power inductor, 74 A Irms, 85 A Isat, DCR 0.18 mOhm, 10.8 x 8.0 mm package./p
    • Product Details
    • Download

    FP1008R6-R150-R at a glance: 150 nH high frequency, high current power inductor, 74 A Irms, 85 A Isat, DCR 0.18 mOhm, 10.8 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1008R6-R150-R High frequency, high current power inductors

    FP1008R6-R150-R is one of Eaton's high frequency, high current power inductor series, 10.8 x 8.0 mm with a 8.0 mm tall profile. Electrically it offers 150 nH at 74 A Irms and 0.18 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP1008R6-R150-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)108 nH
    Irms (40 °C rise, no core loss)74 A
    Isat (20% roll-off @ +25 °C)85 A
    Isat2 (20% roll-off @ +100 °C)68 A
    Isat3 (20% roll-off @ +125 °C)64 A
    DCR typical @ +20 °C0.18 mOhm
    K-factor (Bp-p = K x L x dI)342
    Package10.8 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    150 nH open-circuit, 108 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 85 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 986 mW dissipated at 74 A through 0.18 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 342 turns ripple into flux: a peak-to-peak swing of 25.5 A gives about 130.8 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Series Positioning

    The 10.8 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 13 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.18 mOhm, which is what the extra turns cost, Irms of 74 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    The order of checks that works: compute ripple from 150 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.18 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1008R6-R150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products