
FP1008R6-R220-R at a glance: 220 nH high frequency, high current power inductor, 74 A Irms, 58 A Isat, DCR 0.18 mOhm, 10.8 x 8.0 mm body, 8.0 mm tall.
FP1008R6-R220-R is one of Eaton's high frequency, high current power inductor series, 10.8 x 8.0 mm with a 8.0 mm tall profile. Electrically it offers 220 nH at 74 A Irms and 0.18 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP1008R6-R220-R |
| Inductance, OCL (0 Adc) | 220 nH |
| Inductance, FLL (minimum) | 158 nH |
| Irms (40 °C rise, no core loss) | 74 A |
| Isat (20% roll-off @ +25 °C) | 58 A |
| Isat2 (20% roll-off @ +100 °C) | 44 A |
| Isat3 (20% roll-off @ +125 °C) | 42 A |
| DCR typical @ +20 °C | 0.18 mOhm |
| K-factor (Bp-p = K x L x dI) | 342 |
| Package | 10.8 x 8.0 mm, 8.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
Two inductance figures are published. 220 nH is measured with no DC in the winding, 158 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.
The first Isat column, 58 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.
Irms of 74 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.18 mOhm that is roughly 986 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
Flux swing follows Bp-p = K x L x dI. With K = 342 and a ripple of 17.4 A the core sees roughly 130.9 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.
The 10.8 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 220 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 8 of 13 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.18 mOhm, which is what the extra turns cost, Irms of 74 A is the bottom of the family.
Size the inductor on peak current first, not average. With 220 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.18 mOhm the winding is not the loss, the trace can be.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Why is the saturation current listed at several temperatures?
Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.
What does the R suffix on the part number mean?
It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd