
FP1008R6-R270-R at a glance: 270 nH high frequency, high current power inductor, 74 A Irms, 44 A Isat, DCR 0.18 mOhm, 10.8 x 8.0 mm body, 8.0 mm tall.
The FP1008R6-R270-R is a 10.8 x 8.0 mm high frequency, high current power inductor from Eaton, rated 74 A Irms at 270 nH and 0.18 mOhm typical DCR. It is a surface-mount part 8.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.
| Orderable part number | FP1008R6-R270-R |
| Inductance, OCL (0 Adc) | 270 nH |
| Inductance, FLL (minimum) | 194 nH |
| Irms (40 °C rise, no core loss) | 74 A |
| Isat (20% roll-off @ +25 °C) | 44 A |
| Isat2 (20% roll-off @ +100 °C) | 34 A |
| Isat3 (20% roll-off @ +125 °C) | 32 A |
| DCR typical @ +20 °C | 0.18 mOhm |
| K-factor (Bp-p = K x L x dI) | 342 |
| Package | 10.8 x 8.0 mm, 8.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 270 nH. Put Isat1 through it and the figure falls to 194 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 270 nH number; loop stability and worst-case current belong on the lower one.
The first Isat column, 44 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.
Copper loss at the rated current works out at about 986 mW (74 A squared times 0.18 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
The K-factor of 342 turns ripple into flux: a peak-to-peak swing of 13.2 A gives about 121.9 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.
The 10.8 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 270 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.
That makes it part 10 of 13 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.18 mOhm, which is what the extra turns cost, Irms of 74 A is the bottom of the family.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 270 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
On the board, place the part so the switch-node copper is short and wide. At 0.18 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd