Eaton FP1008R7-R120-R 120 nH 90 A Saturation Inductor
Eaton FP1008R7-R120-R 120 nH 90 A Saturation Inductor

Eaton FP1008R7-R120-R 120 nH 90 A Saturation Inductor

Share
pEaton FP1008R7-R120-R: 120 nH high frequency, high current power inductor, 72 A Irms, 90 A Isat, DCR 0.12 mOhm, 10.8 x 8.2 mm package./p
    • Product Details
    • Download

    FP1008R7-R120-R at a glance: 120 nH high frequency, high current power inductor, 72 A Irms, 90 A Isat, DCR 0.12 mOhm, 10.8 x 8.2 mm body, 8.2 mm tall.

    Eaton FP1008R7-R120-R High frequency, high current power inductors

    Eaton FP1008R7-R120-R is a high frequency, high current power inductor in a 10.8 x 8.2 mm surface-mount package. It carries 120 nH of open-circuit inductance with 72 A Irms and a typical DCR of 0.12 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 8.2 mm tall and rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1008R7-R120-R
    Inductance, OCL (0 Adc)120 nH
    Inductance, FLL (minimum)86 nH
    Irms (40 °C rise, no core loss)72 A
    Isat (20% roll-off @ +25 °C)90 A
    Isat2 (20% roll-off @ +100 °C)75 A
    Isat3 (20% roll-off @ +125 °C)70 A
    DCR typical @ +20 °C0.12 mOhm
    K-factor (Bp-p = K x L x dI)361
    Package10.8 x 8.2 mm, 8.2 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    120 nH open-circuit, 86 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    The first Isat column, 90 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 622 mW dissipated at 72 A through 0.12 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 117 mT for a 27 A ripple (K = 361). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Where This Part Sits in the Range

    The 10.8 x 8.2 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 2 of 4 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Size the inductor on peak current first, not average. With 120 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.12 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1008R7-R120-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message