Eaton FP1008R7-R180-R - 180 nH Shielded Power Inductor 10.8 x 8.2 mm
Eaton FP1008R7-R180-R - 180 nH Shielded Power Inductor 10.8 x 8.2 mm

Eaton FP1008R7-R180-R - 180 nH Shielded Power Inductor 10.8 x 8.2 mm

Share
pEaton FP1008R7-R180-R: 180 nH high frequency, high current power inductor, 72 A Irms, 60 A Isat, DCR 0.12 mOhm, 10.8 x 8.2 mm package./p
    • Product Details
    • Download

    FP1008R7-R180-R at a glance: 180 nH high frequency, high current power inductor, 72 A Irms, 60 A Isat, DCR 0.12 mOhm, 10.8 x 8.2 mm body, 8.2 mm tall.

    Eaton FP1008R7-R180-R High frequency, high current power inductors

    Eaton FP1008R7-R180-R is a high frequency, high current power inductor in a 10.8 x 8.2 mm surface-mount package. It carries 180 nH of open-circuit inductance with 72 A Irms and a typical DCR of 0.12 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 8.2 mm tall and rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP1008R7-R180-R
    Inductance, OCL (0 Adc)180 nH
    Inductance, FLL (minimum)130 nH
    Irms (40 °C rise, no core loss)72 A
    Isat (20% roll-off @ +25 °C)60 A
    Isat2 (20% roll-off @ +100 °C)50 A
    Isat3 (20% roll-off @ +125 °C)46 A
    DCR typical @ +20 °C0.12 mOhm
    K-factor (Bp-p = K x L x dI)361
    Package10.8 x 8.2 mm, 8.2 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    At zero bias the winding measures 180 nH. Put Isat1 through it and the figure falls to 130 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 180 nH number; loop stability and worst-case current belong on the lower one.

    Saturation is quoted as 20% roll-off at 60 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    The 622 mW dissipated at 72 A through 0.12 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 361 and a ripple of 18 A the core sees roughly 117 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    What This Family Is For

    The 10.8 x 8.2 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 180 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the highest inductance of the 4 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 180 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.12 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1008R7-R180-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products