
FP1010R1-R120-R at a glance: 120 nH high frequency, high current power inductor, 50 A Irms, 94 A Isat, DCR 0.185 mOhm, 9.6 x 6.4 mm body, 10.4 mm tall.
Eaton FP1010R1-R120-R is a high frequency, high current power inductor in a 9.6 x 6.4 mm surface-mount package. It carries 120 nH of open-circuit inductance with 50 A Irms and a typical DCR of 0.185 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 10.4 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP1010R1-R120-R |
| Inductance, OCL (0 Adc) | 120 nH |
| Inductance, FLL (minimum) | 84 nH |
| Irms (40 °C rise, no core loss) | 50 A |
| Isat (20% roll-off @ +25 °C) | 94 A |
| Isat3 (20% roll-off @ +100 °C) | 80 A |
| Isat4 (20% roll-off @ +125 °C) | 75 A |
| DCR typical @ +20 °C | 0.185 mOhm |
| K-factor (Bp-p = K x L x dI) | 371 |
| Package | 9.6 x 6.4 mm, 10.4 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
Two inductance figures are published. 120 nH is measured with no DC in the winding, 84 nH with the winding loaded to Isat1. The gap between them is 30%, and it is the reason a converter that looks well damped at no load can ring at full current.
Peak current at 20% roll-off is 94 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
Copper loss at the rated current works out at about 462 mW (50 A squared times 0.185 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
Core loss needs flux, and flux here is about 125.5 mT for a 28.2 A ripple (K = 371). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
The 9.6 x 6.4 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 3 of 12 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.185 mOhm, which is what the extra turns cost, Irms of 50 A is the bottom of the family.
The order of checks that works: compute ripple from 120 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.185 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd