
FP1010R3-R100-R at a glance: 100 nH high frequency, high current power inductor, 78 A Irms, 95 A Isat, DCR 0.145 mOhm, 9.6 x 6.4 mm body, 10.4 mm tall.
Eaton builds the FP1010R3-R100-R as a high frequency, high current power inductor for 9.6 x 6.4 mm footprints. At 100 nH and 78 A Irms with 0.145 mOhm of DCR it targets high-current DC-DC stages; the 10.4 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.
| Orderable part number | FP1010R3-R100-R |
| Inductance, OCL (0 Adc) | 100 nH |
| Inductance, FLL (minimum) | 72 nH |
| Irms (40 °C rise, no core loss) | 78 A |
| Isat (20% roll-off @ +25 °C) | 95 A |
| Isat2 (20% roll-off @ +75 °C) | 88 A |
| Isat3 (20% roll-off @ +100 °C) | 82 A |
| Isat4 (20% roll-off @ +125 °C) | 77 A |
| DCR typical @ +20 °C | 0.145 mOhm |
| K-factor (Bp-p = K x L x dI) | 432 |
| Package | 9.6 x 6.4 mm, 10.4 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 100 nH. Put Isat1 through it and the figure falls to 72 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 100 nH number; loop stability and worst-case current belong on the lower one.
Saturation is quoted as 20% roll-off at 95 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.
Copper loss at the rated current works out at about 882 mW (78 A squared times 0.145 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
Core loss needs flux, and flux here is about 123.1 mT for a 28.5 A ripple (K = 432). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
The 9.6 x 6.4 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.
That makes it part 2 of 12 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.145 mOhm, Irms of 78 A is the top of the family.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 100 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
On the board, place the part so the switch-node copper is short and wide. At 0.145 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

What does the R suffix on the part number mean?
It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.
How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd