Eaton FP1010R3-R220-R 220 nH Power Inductor, 78 A
Eaton FP1010R3-R220-R 220 nH Power Inductor, 78 A

Eaton FP1010R3-R220-R 220 nH Power Inductor, 78 A

Share
pEaton FP1010R3-R220-R: 220 nH high frequency, high current power inductor, 78 A Irms, 38 A Isat, DCR 0.145 mOhm, 9.6 x 6.4 mm package./p
    • Product Details
    • Download

    FP1010R3-R220-R at a glance: 220 nH high frequency, high current power inductor, 78 A Irms, 38 A Isat, DCR 0.145 mOhm, 9.6 x 6.4 mm body, 10.4 mm tall.

    Eaton FP1010R3-R220-R High frequency, high current power inductors

    The FP1010R3-R220-R is a 9.6 x 6.4 mm high frequency, high current power inductor from Eaton, rated 78 A Irms at 220 nH and 0.145 mOhm typical DCR. It is a surface-mount part 10.4 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP1010R3-R220-R
    Inductance, OCL (0 Adc)220 nH
    Inductance, FLL (minimum)158 nH
    Irms (40 °C rise, no core loss)78 A
    Isat (20% roll-off @ +25 °C)38 A
    Isat2 (20% roll-off @ +75 °C)36 A
    Isat3 (20% roll-off @ +100 °C)34 A
    Isat4 (20% roll-off @ +125 °C)31 A
    DCR typical @ +20 °C0.145 mOhm
    K-factor (Bp-p = K x L x dI)432
    Package9.6 x 6.4 mm, 10.4 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    At zero bias the winding measures 220 nH. Put Isat1 through it and the figure falls to 158 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 220 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 38 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 882 mW dissipated at 78 A through 0.145 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 108.3 mT for a 11.4 A ripple (K = 432). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Where This Part Sits in the Range

    The 9.6 x 6.4 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 220 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 8 of 12 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.145 mOhm, Irms of 78 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 220 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.145 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1010R3-R220-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products