Eaton FP1010R3-R270-R - 270 nH Shielded Power Inductor 9.6 x 6.4 mm
Eaton FP1010R3-R270-R - 270 nH Shielded Power Inductor 9.6 x 6.4 mm

Eaton FP1010R3-R270-R - 270 nH Shielded Power Inductor 9.6 x 6.4 mm

Share
pEaton FP1010R3-R270-R: 270 nH high frequency, high current power inductor, 78 A Irms, 30 A Isat, DCR 0.145 mOhm, 9.6 x 6.4 mm package./p
    • Product Details
    • Download

    FP1010R3-R270-R at a glance: 270 nH high frequency, high current power inductor, 78 A Irms, 30 A Isat, DCR 0.145 mOhm, 9.6 x 6.4 mm body, 10.4 mm tall.

    Eaton FP1010R3-R270-R High frequency, high current power inductors

    The FP1010R3-R270-R is a 9.6 x 6.4 mm high frequency, high current power inductor from Eaton, rated 78 A Irms at 270 nH and 0.145 mOhm typical DCR. It is a surface-mount part 10.4 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP1010R3-R270-R
    Inductance, OCL (0 Adc)270 nH
    Inductance, FLL (minimum)194 nH
    Irms (40 °C rise, no core loss)78 A
    Isat (20% roll-off @ +25 °C)30 A
    Isat2 (20% roll-off @ +75 °C)29 A
    Isat3 (20% roll-off @ +100 °C)27 A
    Isat4 (20% roll-off @ +125 °C)24 A
    DCR typical @ +20 °C0.145 mOhm
    K-factor (Bp-p = K x L x dI)432
    Package9.6 x 6.4 mm, 10.4 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two inductance figures are published. 270 nH is measured with no DC in the winding, 194 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 30 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 882 mW (78 A squared times 0.145 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 432 and a ripple of 9 A the core sees roughly 105 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    What This Family Is For

    The 9.6 x 6.4 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 270 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 9 of 12 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.145 mOhm, Irms of 78 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 270 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.145 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1010R3-R270-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message