
FP1010V1-R100-R at a glance: 100 nH high frequency, high current power inductor, 68 A Irms, 97 A Isat, DCR 0.145 mOhm, 10.0 x 7.0 mm body, 10.0 mm tall.
Eaton FP1010V1-R100-R is a high frequency, high current power inductor in a 10.0 x 7.0 mm surface-mount package. It carries 100 nH of open-circuit inductance with 68 A Irms and a typical DCR of 0.145 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 10.0 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP1010V1-R100-R |
| Inductance, OCL (0 Adc) | 100 nH |
| Inductance, FLL (minimum) | 72 nH |
| Irms (40 °C rise, no core loss) | 68 A |
| Isat (20% roll-off @ +25 °C) | 97 A |
| Isat2 (20% roll-off @ +75 °C) | 88 A |
| Isat3 (20% roll-off @ +100 °C) | 85 A |
| DCR typical @ +20 °C | 0.145 mOhm |
| K-factor (Bp-p = K x L x dI) | 352 |
| Package | 10.0 x 7.0 mm, 10.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
Two inductance figures are published. 100 nH is measured with no DC in the winding, 72 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.
Saturation is quoted as 20% roll-off at 97 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.
Copper loss at the rated current works out at about 670 mW (68 A squared times 0.145 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
Flux swing follows Bp-p = K x L x dI. With K = 352 and a ripple of 29.1 A the core sees roughly 102.4 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.
The 10.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.
That makes it the lowest inductance of the 11 parts in this data sheet, and it shares the lowest DCR here at 0.145 mOhm, Irms of 68 A is the top of the family.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 100 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.145 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd