Eaton FP1010V11-R090-R 90 nH 105 A Saturation Inductor
Eaton FP1010V11-R090-R 90 nH 105 A Saturation Inductor

Eaton FP1010V11-R090-R 90 nH 105 A Saturation Inductor

Share
pEaton FP1010V11-R090-R: 90 nH high frequency, high current power inductor, 61 A Irms, 105 A Isat, DCR 0.2 mOhm, 10.0 x 4.5 mm package./p
    • Product Details
    • Download

    FP1010V11-R090-R at a glance: 90 nH high frequency, high current power inductor, 61 A Irms, 105 A Isat, DCR 0.2 mOhm, 10.0 x 4.5 mm body, 10.0 mm tall.

    Eaton FP1010V11-R090-R High frequency, high current power inductors

    FP1010V11-R090-R is one of Eaton's high frequency, high current power inductor series, 10.0 x 4.5 mm with a 10.0 mm tall profile. Electrically it offers 90 nH at 61 A Irms and 0.2 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Electrical Specifications

    Orderable part numberFP1010V11-R090-R
    Inductance, OCL (0 Adc)90 nH
    Inductance, FLL (minimum)64 nH
    Irms (40 °C rise, no core loss)61 A
    Isat (20% roll-off @ +25 °C)105 A
    Isat2 (20% roll-off @ +100 °C)90 A
    Isat3 (20% roll-off @ +125 °C)84 A
    DCR typical @ +20 °C0.2 mOhm
    K-factor (Bp-p = K x L x dI)460
    Package10.0 x 4.5 mm, 10.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    90 nH open-circuit, 64 nH at full load: that is a 29% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    The first Isat column, 105 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 744 mW dissipated at 61 A through 0.2 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 130.4 mT for a 31.5 A ripple (K = 460). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Where This Part Sits in the Range

    The 10.0 x 4.5 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 90 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    • Application fit: Multi-phase and Vcore regulators, Voltage regulator modules (VRMs) and high power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Size the inductor on peak current first, not average. With 90 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.2 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1010V11-R090-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message