Eaton FP1010V5-R100-R 100 nH 117 A Saturation Inductor
Eaton FP1010V5-R100-R 100 nH 117 A Saturation Inductor

Eaton FP1010V5-R100-R 100 nH 117 A Saturation Inductor

Share
pEaton FP1010V5-R100-R: 100 nH high frequency, high current power inductor, 68 A Irms, 117 A Isat, DCR 0.185 mOhm, 10.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP1010V5-R100-R at a glance: 100 nH high frequency, high current power inductor, 68 A Irms, 117 A Isat, DCR 0.185 mOhm, 10.0 x 7.0 mm body, 10.0 mm tall.

    Eaton FP1010V5-R100-R High frequency, high current power inductors

    Eaton builds the FP1010V5-R100-R as a high frequency, high current power inductor for 10.0 x 7.0 mm footprints. At 100 nH and 68 A Irms with 0.185 mOhm of DCR it targets high-current DC-DC stages; the 10.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1010V5-R100-R
    Inductance, OCL (0 Adc)100 nH
    Inductance, FLL (minimum)72 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)117 A
    Isat2 (20% roll-off @ +75 °C)97 A
    Isat3 (20% roll-off @ +100 °C)94 A
    DCR typical @ +20 °C0.185 mOhm
    K-factor (Bp-p = K x L x dI)308
    Package10.0 x 7.0 mm, 10.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two inductance figures are published. 100 nH is measured with no DC in the winding, 72 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 117 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 855 mW (68 A squared times 0.185 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 308 and a ripple of 35.1 A the core sees roughly 108.1 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Where This Part Sits in the Range

    The 10.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 11 parts in this data sheet, DCR sits between the 0.145 and 0.4 mOhm the series covers, Irms of 68 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 100 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.185 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1010V5-R100-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message