
FP1010V5-R120-R at a glance: 120 nH high frequency, high current power inductor, 68 A Irms, 98 A Isat, DCR 0.185 mOhm, 10.0 x 7.0 mm body, 10.0 mm tall.
Eaton FP1010V5-R120-R is a high frequency, high current power inductor in a 10.0 x 7.0 mm surface-mount package. It carries 120 nH of open-circuit inductance with 68 A Irms and a typical DCR of 0.185 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 10.0 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP1010V5-R120-R |
| Inductance, OCL (0 Adc) | 120 nH |
| Inductance, FLL (minimum) | 86 nH |
| Irms (40 °C rise, no core loss) | 68 A |
| Isat (20% roll-off @ +25 °C) | 98 A |
| Isat2 (20% roll-off @ +75 °C) | 82 A |
| Isat3 (20% roll-off @ +100 °C) | 79 A |
| DCR typical @ +20 °C | 0.185 mOhm |
| K-factor (Bp-p = K x L x dI) | 308 |
| Package | 10.0 x 7.0 mm, 10.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 120 nH. Put Isat1 through it and the figure falls to 86 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 120 nH number; loop stability and worst-case current belong on the lower one.
The first Isat column, 98 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.
Copper loss at the rated current works out at about 855 mW (68 A squared times 0.185 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
Flux swing follows Bp-p = K x L x dI. With K = 308 and a ripple of 29.4 A the core sees roughly 108.7 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.
The 10.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 3 of 11 when the data sheet is sorted by inductance, DCR sits between the 0.145 and 0.4 mOhm the series covers, Irms of 68 A is the top of the family.
Size the inductor on peak current first, not average. With 120 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.
On the board, place the part so the switch-node copper is short and wide. At 0.185 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Can I substitute a lower inductance in the same body?
Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd