Eaton FP1010V5-R150-R - 150 nH Shielded Power Inductor 10.0 x 7.0 mm
Eaton FP1010V5-R150-R - 150 nH Shielded Power Inductor 10.0 x 7.0 mm

Eaton FP1010V5-R150-R - 150 nH Shielded Power Inductor 10.0 x 7.0 mm

Share
pEaton FP1010V5-R150-R: 150 nH high frequency, high current power inductor, 68 A Irms, 85 A Isat, DCR 0.185 mOhm, 10.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP1010V5-R150-R at a glance: 150 nH high frequency, high current power inductor, 68 A Irms, 85 A Isat, DCR 0.185 mOhm, 10.0 x 7.0 mm body, 10.0 mm tall.

    Eaton FP1010V5-R150-R High frequency, high current power inductors

    FP1010V5-R150-R is one of Eaton's high frequency, high current power inductor series, 10.0 x 7.0 mm with a 10.0 mm tall profile. Electrically it offers 150 nH at 68 A Irms and 0.185 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Electrical Specifications

    Orderable part numberFP1010V5-R150-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)108 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)85 A
    Isat2 (20% roll-off @ +75 °C)75 A
    Isat3 (20% roll-off @ +100 °C)73 A
    DCR typical @ +20 °C0.185 mOhm
    K-factor (Bp-p = K x L x dI)308
    Package10.0 x 7.0 mm, 10.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    At zero bias the winding measures 150 nH. Put Isat1 through it and the figure falls to 108 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 150 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 85 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 68 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.185 mOhm that is roughly 855 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 308 turns ripple into flux: a peak-to-peak swing of 25.5 A gives about 117.8 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    The 10.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 5 of 11 when the data sheet is sorted by inductance, DCR sits between the 0.145 and 0.4 mOhm the series covers, Irms of 68 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 150 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.185 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1010V5-R150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products