Eaton FP1010V5-R330-R High Current Inductor, 330 nH 0.185 mOhm
Eaton FP1010V5-R330-R High Current Inductor, 330 nH 0.185 mOhm

Eaton FP1010V5-R330-R High Current Inductor, 330 nH 0.185 mOhm

Share
pEaton FP1010V5-R330-R: 330 nH high frequency, high current power inductor, 68 A Irms, 35 A Isat, DCR 0.185 mOhm, 10.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP1010V5-R330-R at a glance: 330 nH high frequency, high current power inductor, 68 A Irms, 35 A Isat, DCR 0.185 mOhm, 10.0 x 7.0 mm body, 10.0 mm tall.

    Eaton FP1010V5-R330-R High frequency, high current power inductors

    The FP1010V5-R330-R is a 10.0 x 7.0 mm high frequency, high current power inductor from Eaton, rated 68 A Irms at 330 nH and 0.185 mOhm typical DCR. It is a surface-mount part 10.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP1010V5-R330-R
    Inductance, OCL (0 Adc)330 nH
    Inductance, FLL (minimum)237 nH
    Irms (40 °C rise, no core loss)68 A
    Isat (20% roll-off @ +25 °C)35 A
    Isat2 (20% roll-off @ +75 °C)29 A
    Isat3 (20% roll-off @ +100 °C)27 A
    DCR typical @ +20 °C0.185 mOhm
    K-factor (Bp-p = K x L x dI)308
    Package10.0 x 7.0 mm, 10.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Two inductance figures are published. 330 nH is measured with no DC in the winding, 237 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 35 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 68 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.185 mOhm that is roughly 855 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 308 and a ripple of 10.5 A the core sees roughly 106.7 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    What This Family Is For

    The 10.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 330 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 8 of 11 when the data sheet is sorted by inductance, DCR sits between the 0.145 and 0.4 mOhm the series covers, Irms of 68 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 330 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.185 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1010V5-R330-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message