Eaton FP1010V6-R330-R 54 A SMD Power Inductor, 330 nH
Eaton FP1010V6-R330-R 54 A SMD Power Inductor, 330 nH

Eaton FP1010V6-R330-R 54 A SMD Power Inductor, 330 nH

Share
pEaton FP1010V6-R330-R: 330 nH high frequency, high current power inductor, 54 A Irms, 40 A Isat, DCR 0.4 mOhm, 10.0 x 7.0 mm package./p
    • Product Details
    • Download

    FP1010V6-R330-R at a glance: 330 nH high frequency, high current power inductor, 54 A Irms, 40 A Isat, DCR 0.4 mOhm, 10.0 x 7.0 mm body, 10.0 mm tall.

    Eaton FP1010V6-R330-R High frequency, high current power inductors

    Eaton FP1010V6-R330-R is a high frequency, high current power inductor in a 10.0 x 7.0 mm surface-mount package. It carries 330 nH of open-circuit inductance with 54 A Irms and a typical DCR of 0.4 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 10.0 mm tall and rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP1010V6-R330-R
    Inductance, OCL (0 Adc)330 nH
    Inductance, FLL (minimum)231 nH
    Irms (40 °C rise, no core loss)54 A
    Isat (20% roll-off @ +25 °C)40 A
    Isat2 (20% roll-off @ +75 °C)32 A
    Isat3 (20% roll-off @ +100 °C)30 A
    DCR typical @ +20 °C0.4 mOhm
    K-factor (Bp-p = K x L x dI)216
    Package10.0 x 7.0 mm, 10.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two inductance figures are published. 330 nH is measured with no DC in the winding, 231 nH with the winding loaded to Isat1. The gap between them is 30%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 40 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 1166 mW dissipated at 54 A through 0.4 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 85.5 mT for a 12 A ripple (K = 216). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 10.0 x 7.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 330 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 8 of 11 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.4 mOhm, which is what the extra turns cost.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs) and high- power density VRMs, Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 330 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.4 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1010V6-R330-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message