
FP1012V3-R330-R at a glance: 330 nH high frequency, high current power inductor, 84 A Irms, 40 A Isat, DCR 0.125 mOhm, 10.0 x 6.0 mm body, 12.0 mm tall.
The FP1012V3-R330-R is a 10.0 x 6.0 mm high frequency, high current power inductor from Eaton, rated 84 A Irms at 330 nH and 0.125 mOhm typical DCR. It is a surface-mount part 12.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.
| Orderable part number | FP1012V3-R330-R |
| Inductance, OCL (0 Adc) | 330 nH |
| Inductance, FLL (minimum) | 231 nH |
| Irms (40 °C rise, no core loss) | 84 A |
| Isat (20% roll-off @ +25 °C) | 40 A |
| Isat2 (20% roll-off @ +100 °C) | 32 A |
| Isat3 (20% roll-off @ +125 °C) | 30 A |
| DCR typical @ +20 °C | 0.125 mOhm |
| K-factor (Bp-p = K x L x dI) | 305 |
| Package | 10.0 x 6.0 mm, 12.0 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
Two inductance figures are published. 330 nH is measured with no DC in the winding, 231 nH with the winding loaded to Isat1. The gap between them is 30%, and it is the reason a converter that looks well damped at no load can ring at full current.
Peak current at 20% roll-off is 40 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
Irms of 84 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.125 mOhm that is roughly 882 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
Core loss needs flux, and flux here is about 120.8 mT for a 12 A ripple (K = 305). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
The 10.0 x 6.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 330 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.
That makes it part 14 of 16 when the data sheet is sorted by inductance.
Size the inductor on peak current first, not average. With 330 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.125 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd