Eaton FP1105R1-R12-R High Current Inductor, 120 nH 0.35 mOhm
Eaton FP1105R1-R12-R High Current Inductor, 120 nH 0.35 mOhm

Eaton FP1105R1-R12-R High Current Inductor, 120 nH 0.35 mOhm

Share
pEaton FP1105R1-R12-R: 120 nH high current power inductor, 46 A Irms, 66 A Isat, DCR 0.35 mOhm, 11.0 x 8.0 mm package./p
    • Product Details
    • Download

    FP1105R1-R12-R at a glance: 120 nH high current power inductor, 46 A Irms, 66 A Isat, DCR 0.35 mOhm, 11.0 x 8.0 mm body, 4.9 mm tall.

    Eaton FP1105R1-R12-R High current power inductors

    FP1105R1-R12-R is one of Eaton's high current power inductor series, 11.0 x 8.0 mm with a 4.9 mm tall profile. Electrically it offers 120 nH at 46 A Irms and 0.35 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Specification Table

    Orderable part numberFP1105R1-R12-R
    Inductance, OCL (0 Adc)120 nH
    Inductance, FLL (minimum)86 nH
    Irms (40 °C rise, no core loss)46 A
    Isat (20% roll-off @ +25 °C)66 A
    Isat2 (20% roll-off @ +125 °C)50 A
    DCR typical @ +20 °C0.35 mOhm
    K-factor (Bp-p = K x L x dI)467
    Package11.0 x 8.0 mm, 4.9 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Two inductance figures are published. 120 nH is measured with no DC in the winding, 86 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    The first Isat column, 66 A at +25 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    The 741 mW dissipated at 46 A through 0.35 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Core loss needs flux, and flux here is about 111 mT for a 19.8 A ripple (K = 467). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    The 11.0 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 2 of 5 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase regulators, Voltage Regulator Module (VRM), Portable electronics.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 120 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.35 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1105R1-R12-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products