
FP1105R1-R15-R at a glance: 150 nH high current power inductor, 46 A Irms, 54 A Isat, DCR 0.35 mOhm, 11.0 x 8.0 mm body, 4.9 mm tall.
Eaton FP1105R1-R15-R is a high current power inductor in a 11.0 x 8.0 mm surface-mount package. It carries 150 nH of open-circuit inductance with 46 A Irms and a typical DCR of 0.35 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 4.9 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP1105R1-R15-R |
| Inductance, OCL (0 Adc) | 150 nH |
| Inductance, FLL (minimum) | 109 nH |
| Irms (40 °C rise, no core loss) | 46 A |
| Isat (20% roll-off @ +25 °C) | 54 A |
| Isat2 (20% roll-off @ +125 °C) | 42 A |
| DCR typical @ +20 °C | 0.35 mOhm |
| K-factor (Bp-p = K x L x dI) | 467 |
| Package | 11.0 x 8.0 mm, 4.9 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
Two inductance figures are published. 150 nH is measured with no DC in the winding, 109 nH with the winding loaded to Isat1. The gap between them is 27%, and it is the reason a converter that looks well damped at no load can ring at full current.
Peak current at 20% roll-off is 54 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
The 741 mW dissipated at 46 A through 0.35 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
The K-factor of 467 turns ripple into flux: a peak-to-peak swing of 16.2 A gives about 113.5 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.
The 11.0 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 3 of 5 when the data sheet is sorted by inductance.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 150 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
On the board, place the part so the switch-node copper is short and wide. At 0.35 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Why is the saturation current listed at several temperatures?
Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.
Can I substitute a lower inductance in the same body?
Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd