
FP1105R1-R20-R at a glance: 192 nH high current power inductor, 46 A Irms, 42 A Isat, DCR 0.35 mOhm, 11.0 x 8.0 mm body, 4.9 mm tall.
FP1105R1-R20-R is one of Eaton's high current power inductor series, 11.0 x 8.0 mm with a 4.9 mm tall profile. Electrically it offers 192 nH at 46 A Irms and 0.35 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP1105R1-R20-R |
| Inductance, OCL (0 Adc) | 192 nH |
| Inductance, FLL (minimum) | 138 nH |
| Irms (40 °C rise, no core loss) | 46 A |
| Isat (20% roll-off @ +25 °C) | 42 A |
| Isat2 (20% roll-off @ +125 °C) | 34 A |
| DCR typical @ +20 °C | 0.35 mOhm |
| K-factor (Bp-p = K x L x dI) | 467 |
| Package | 11.0 x 8.0 mm, 4.9 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
192 nH open-circuit, 138 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.
Saturation is quoted as 20% roll-off at 42 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.
The 741 mW dissipated at 46 A through 0.35 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.
Flux swing follows Bp-p = K x L x dI. With K = 467 and a ripple of 12.6 A the core sees roughly 113 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.
The 11.0 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 192 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 4 of 5 when the data sheet is sorted by inductance.
Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 192 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.35 mOhm the winding is not the loss, the trace can be.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Why is the saturation current listed at several temperatures?
Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.
Why does DCR have both a typical and a maximum figure?
The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd