Eaton FP1107R1-R07-R - 70 nH Shielded Power Inductor 11.2 x 8.0 mm
Eaton FP1107R1-R07-R - 70 nH Shielded Power Inductor 11.2 x 8.0 mm

Eaton FP1107R1-R07-R - 70 nH Shielded Power Inductor 11.2 x 8.0 mm

Share
pEaton FP1107R1-R07-R: 70 nH high frequency, high current power inductor, 55 A Irms, 140 A Isat, DCR 0.29 mOhm, 11.2 x 8.0 mm package./p
    • Product Details
    • Download

    FP1107R1-R07-R at a glance: 70 nH high frequency, high current power inductor, 55 A Irms, 140 A Isat, DCR 0.29 mOhm, 11.2 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1107R1-R07-R High frequency, high current power inductors

    Eaton builds the FP1107R1-R07-R as a high frequency, high current power inductor for 11.2 x 8.0 mm footprints. At 70 nH and 55 A Irms with 0.29 mOhm of DCR it targets high-current DC-DC stages; the 7.5 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1107R1-R07-R
    Inductance, OCL (0 Adc)70 nH
    Inductance, FLL (minimum)50 nH
    Irms (40 °C rise, no core loss)55 A
    Isat (20% roll-off @ +25 °C)140 A
    Isat4 (20% roll-off @ +125 °C)123 A
    DCR typical @ +20 °C0.29 mOhm
    K-factor (Bp-p = K x L x dI)361.1
    Package11.2 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Two inductance figures are published. 70 nH is measured with no DC in the winding, 50 nH with the winding loaded to Isat1. The gap between them is 29%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 140 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 877 mW (55 A squared times 0.29 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 106.2 mT for a 42 A ripple (K = 361.1). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 11.2 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 70 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.

    That makes it the lowest inductance of the 22 parts in this data sheet, and it shares the lowest DCR here at 0.29 mOhm, Irms of 55 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Size the inductor on peak current first, not average. With 70 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.29 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1107R1-R07-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products