Eaton FP1107R2-R30-R High Current Inductor, 300 nH 0.47 mOhm
Eaton FP1107R2-R30-R High Current Inductor, 300 nH 0.47 mOhm

Eaton FP1107R2-R30-R High Current Inductor, 300 nH 0.47 mOhm

Share
pEaton FP1107R2-R30-R: 300 nH high frequency, high current power inductor, 42 A Irms, 35 A Isat, DCR 0.47 mOhm, 11.2 x 8.0 mm package./p
    • Product Details
    • Download

    FP1107R2-R30-R at a glance: 300 nH high frequency, high current power inductor, 42 A Irms, 35 A Isat, DCR 0.47 mOhm, 11.2 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1107R2-R30-R High frequency, high current power inductors

    The FP1107R2-R30-R is a 11.2 x 8.0 mm high frequency, high current power inductor from Eaton, rated 42 A Irms at 300 nH and 0.47 mOhm typical DCR. It is a surface-mount part 7.5 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Specification Table

    Orderable part numberFP1107R2-R30-R
    Inductance, OCL (0 Adc)300 nH
    Inductance, FLL (minimum)217 nH
    Irms (40 °C rise, no core loss)42 A
    Isat (20% roll-off @ +25 °C)35 A
    Isat4 (20% roll-off @ +125 °C)28 A
    DCR typical @ +20 °C0.47 mOhm
    K-factor (Bp-p = K x L x dI)363.3
    Package11.2 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    300 nH open-circuit, 217 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 35 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 829 mW (42 A squared times 0.47 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 363.3 turns ripple into flux: a peak-to-peak swing of 10.5 A gives about 114.4 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Positioning in the FP Range

    The 11.2 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 300 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 14 of 22 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.47 mOhm, which is what the extra turns cost, Irms of 42 A is the bottom of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 300 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.47 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1107R2-R30-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products