Eaton FP1107R4-R180-R 180 nH Power Inductor, 50 A
Eaton FP1107R4-R180-R 180 nH Power Inductor, 50 A

Eaton FP1107R4-R180-R 180 nH Power Inductor, 50 A

Share
pEaton FP1107R4-R180-R: 180 nH high frequency, high current power inductor, 50 A Irms, 62 A Isat, DCR 0.29 mOhm, 11.2 x 8.0 mm package./p
    • Product Details
    • Download

    FP1107R4-R180-R at a glance: 180 nH high frequency, high current power inductor, 50 A Irms, 62 A Isat, DCR 0.29 mOhm, 11.2 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1107R4-R180-R High frequency, high current power inductors

    The FP1107R4-R180-R is a 11.2 x 8.0 mm high frequency, high current power inductor from Eaton, rated 50 A Irms at 180 nH and 0.29 mOhm typical DCR. It is a surface-mount part 7.5 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Ratings at a Glance

    Orderable part numberFP1107R4-R180-R
    Inductance, OCL (0 Adc)180 nH
    Inductance, FLL (minimum)130 nH
    Irms (40 °C rise, no core loss)50 A
    Isat (20% roll-off @ +25 °C)62 A
    Isat2 (20% roll-off @ +85 °C)55 A
    Isat3 (20% roll-off @ +100 °C)53 A
    Isat4 (20% roll-off @ +125 °C)50 A
    DCR typical @ +20 °C0.29 mOhm
    K-factor (Bp-p = K x L x dI)361
    Package11.2 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    180 nH open-circuit, 130 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Peak current at 20% roll-off is 62 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 725 mW dissipated at 50 A through 0.29 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    Flux swing follows Bp-p = K x L x dI. With K = 361 and a ripple of 18.6 A the core sees roughly 120.9 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Positioning in the FP Range

    The 11.2 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 180 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 10 of 22 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.29 mOhm.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 180 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.29 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1107R4-R180-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products