Eaton FP1107R5-R510-R High Current Inductor, 510 nH 0.29 mOhm
Eaton FP1107R5-R510-R High Current Inductor, 510 nH 0.29 mOhm

Eaton FP1107R5-R510-R High Current Inductor, 510 nH 0.29 mOhm

Share
pEaton FP1107R5-R510-R: 510 nH high frequency, high current power inductor, 55 A Irms, 18 A Isat, DCR 0.29 mOhm, 11.2 x 8.0 mm package./p
    • Product Details
    • Download

    FP1107R5-R510-R at a glance: 510 nH high frequency, high current power inductor, 55 A Irms, 18 A Isat, DCR 0.29 mOhm, 11.2 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1107R5-R510-R High frequency, high current power inductors

    FP1107R5-R510-R is one of Eaton's high frequency, high current power inductor series, 11.2 x 8.0 mm with a 7.5 mm tall profile. Electrically it offers 510 nH at 55 A Irms and 0.29 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Electrical Specifications

    Orderable part numberFP1107R5-R510-R
    Inductance, OCL (0 Adc)510 nH
    Inductance, FLL (minimum)364 nH
    Irms (40 °C rise, no core loss)55 A
    Isat (20% roll-off @ +25 °C)18 A
    Isat4 (20% roll-off @ +125 °C)14.5 A
    DCR typical @ +20 °C0.29 mOhm
    K-factor (Bp-p = K x L x dI)361.1
    Package11.2 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    Two inductance figures are published. 510 nH is measured with no DC in the winding, 364 nH with the winding loaded to Isat1. The gap between them is 29%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 18 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    The 877 mW dissipated at 55 A through 0.29 mOhm is what sets the 40 °C rise behind the Irms column. Because that figure excludes core loss, a converter running at high frequency with large ripple will heat the part more than the table suggests.

    The K-factor of 361.1 turns ripple into flux: a peak-to-peak swing of 5.4 A gives about 99.4 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    The 11.2 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 510 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 20 of 22 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.29 mOhm, Irms of 55 A is the top of the family.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    The order of checks that works: compute ripple from 510 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.29 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1107R5-R510-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message