Eaton FP1108L1-R150-R 150 nH Power Inductor, 64 A
Eaton FP1108L1-R150-R 150 nH Power Inductor, 64 A

Eaton FP1108L1-R150-R 150 nH Power Inductor, 64 A

Share
pEaton FP1108L1-R150-R: 150 nH high frequency, high current power inductor, 64 A Irms, 57 A Isat, DCR 0.1 mOhm, 11.0 x 8.2 mm package./p
    • Product Details
    • Download

    FP1108L1-R150-R at a glance: 150 nH high frequency, high current power inductor, 64 A Irms, 57 A Isat, DCR 0.1 mOhm, 11.0 x 8.2 mm body, 8.3 mm tall.

    Eaton FP1108L1-R150-R High frequency, high current power inductors

    The FP1108L1-R150-R is a 11.0 x 8.2 mm high frequency, high current power inductor from Eaton, rated 64 A Irms at 150 nH and 0.1 mOhm typical DCR. It is a surface-mount part 8.3 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP1108L1-R150-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)108 nH
    Irms (40 °C rise, no core loss)64 A
    Isat (20% roll-off @ +25 °C)57 A
    Isat2 (20% roll-off @ +75 °C)49 A
    Isat3 (20% roll-off @ +100 °C)45 A
    DCR typical @ +20 °C0.1 mOhm
    K-factor (Bp-p = K x L x dI)422
    Package11.0 x 8.2 mm, 8.3 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Two inductance figures are published. 150 nH is measured with no DC in the winding, 108 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Saturation is quoted as 20% roll-off at 57 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 410 mW (64 A squared times 0.1 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 108.2 mT for a 17.1 A ripple (K = 422). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 11.0 x 8.2 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 2 of 4 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.1 mOhm, Irms of 64 A is the top of the family.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    The order of checks that works: compute ripple from 150 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.1 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1108L1-R150-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message