Eaton FP1108L3-R105-R 91 A SMD Power Inductor, 105 nH
Eaton FP1108L3-R105-R 91 A SMD Power Inductor, 105 nH

Eaton FP1108L3-R105-R 91 A SMD Power Inductor, 105 nH

Share
pEaton FP1108L3-R105-R: 105 nH high frequency, high current power inductor, 91 A Irms, 57 A Isat, DCR 0.05 mOhm, 11.0 x 8.0 mm package./p
    • Product Details
    • Download

    FP1108L3-R105-R at a glance: 105 nH high frequency, high current power inductor, 91 A Irms, 57 A Isat, DCR 0.05 mOhm, 11.0 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1108L3-R105-R High frequency, high current power inductors

    Eaton FP1108L3-R105-R is a high frequency, high current power inductor in a 11.0 x 8.0 mm surface-mount package. It carries 105 nH of open-circuit inductance with 91 A Irms and a typical DCR of 0.05 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 8.0 mm tall and rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1108L3-R105-R
    Inductance, OCL (0 Adc)105 nH
    Inductance, FLL (minimum)76 nH
    Irms (40 °C rise, no core loss)91 A
    Isat (20% roll-off @ +25 °C)57 A
    Isat2 (20% roll-off @ +100 °C)48 A
    Isat3 (20% roll-off @ +125 °C)45 A
    DCR typical @ +20 °C0.05 mOhm
    K-factor (Bp-p = K x L x dI)552
    Package11.0 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    105 nH open-circuit, 76 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 57 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 91 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.05 mOhm that is roughly 414 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 552 turns ripple into flux: a peak-to-peak swing of 17.1 A gives about 99.1 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    The 11.0 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 105 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the lowest inductance of the 4 parts in this data sheet.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 105 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.05 mOhm the winding is not the loss, the trace can be.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1108L3-R105-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message