Eaton FP1108L4-R120-R 120 nH 50 A Saturation Inductor
Eaton FP1108L4-R120-R 120 nH 50 A Saturation Inductor

Eaton FP1108L4-R120-R 120 nH 50 A Saturation Inductor

Share
pEaton FP1108L4-R120-R: 120 nH high frequency, high current power inductor, 91 A Irms, 50 A Isat, DCR 0.05 mOhm, 11.0 x 8.0 mm package./p
    • Product Details
    • Download

    FP1108L4-R120-R at a glance: 120 nH high frequency, high current power inductor, 91 A Irms, 50 A Isat, DCR 0.05 mOhm, 11.0 x 8.0 mm body, 8.0 mm tall.

    Eaton FP1108L4-R120-R High frequency, high current power inductors

    Eaton builds the FP1108L4-R120-R as a high frequency, high current power inductor for 11.0 x 8.0 mm footprints. At 120 nH and 91 A Irms with 0.05 mOhm of DCR it targets high-current DC-DC stages; the 8.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Specification Table

    Orderable part numberFP1108L4-R120-R
    Inductance, OCL (0 Adc)120 nH
    Inductance, FLL (minimum)86 nH
    Irms (40 °C rise, no core loss)91 A
    Isat (20% roll-off @ +25 °C)50 A
    Isat2 (20% roll-off @ +100 °C)42 A
    Isat3 (20% roll-off @ +125 °C)40 A
    DCR typical @ +20 °C0.05 mOhm
    K-factor (Bp-p = K x L x dI)552
    Package11.0 x 8.0 mm, 8.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    Two inductance figures are published. 120 nH is measured with no DC in the winding, 86 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    Peak current at 20% roll-off is 50 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 91 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.05 mOhm that is roughly 414 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 552 and a ripple of 15 A the core sees roughly 99.4 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    Series Positioning

    The 11.0 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 120 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 2 of 4 when the data sheet is sorted by inductance.

    • Application fit: Servers, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 120 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.05 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1108L4-R120-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message