
FP1108R1-R10-R at a glance: 100 nH high frequency, high current power inductor, - A Irms, - A Isat, DCR - mOhm, 11.0 x 8.0 mm body, 7.5 mm tall.
Eaton FP1108R1-R10-R is a high frequency, high current power inductor in a 11.0 x 8.0 mm surface-mount package. It carries 100 nH of open-circuit inductance with - A Irms and a typical DCR of - mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 7.5 mm tall and rated from -40 °C to +125 °C.
| Orderable part number | FP1108R1-R10-R |
| Inductance, OCL (0 Adc) | 100 nH |
| Inductance, FLL (minimum) | 81 nH |
| Isat2 | 96 A |
| Isat3 | 94 A |
| Isat4 | 90 A |
| K-factor (Bp-p = K x L x dI) | 330 |
| Package | 11.0 x 8.0 mm, 7.5 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| RoHS | Compliant (-R suffix) |
100 nH open-circuit, 81 nH at full load: that is a 19% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.
Peak current at the quoted roll-off is - A. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.
Irms of - A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0 mOhm that is roughly 0 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
The data sheet for this part does not publish a K-factor, so core loss has to come from the loss curve rather than from a formula. If the ripple is large, measure it on the bench rather than assuming the 40 °C Irms margin covers it.
The 11.0 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 100 nH this is a low-inductance point for the family, which means high ripple for a given input voltage and duty cycle. That is the intent: these parts are chosen when the converter switches fast and the inductor shapes the ripple rather than storing bulk energy.
That makes it the lowest inductance of the 4 parts in this data sheet.
The order of checks that works: compute ripple from 100 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
On the board, place the part so the switch-node copper is short and wide. At 0 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd