Eaton FP1108R1-R18-R 180 nH 65 A Saturation Inductor
Eaton FP1108R1-R18-R 180 nH 65 A Saturation Inductor

Eaton FP1108R1-R18-R 180 nH 65 A Saturation Inductor

Share
pEaton FP1108R1-R18-R: 180 nH high frequency, high current power inductor, A Irms, 65 A Isat, DCR, mOhm, 11.0 x 8.0 mm package./p
    • Product Details
    • Download

    FP1108R1-R18-R at a glance: 180 nH high frequency, high current power inductor, - A Irms, 65 A Isat, DCR - mOhm, 11.0 x 8.0 mm body, 7.5 mm tall.

    Eaton FP1108R1-R18-R High frequency, high current power inductors

    Eaton builds the FP1108R1-R18-R as a high frequency, high current power inductor for 11.0 x 8.0 mm footprints. At 180 nH and - A Irms with - mOhm of DCR it targets high-current DC-DC stages; the 7.5 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1108R1-R18-R
    Inductance, OCL (0 Adc)180 nH
    Inductance, FLL (minimum)132 nH
    Isat65 A
    Isat261 A
    Isat358 A
    Isat450 A
    K-factor (Bp-p = K x L x dI)330
    Package11.0 x 8.0 mm, 7.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 180 nH. Put Isat1 through it and the figure falls to 132 nH, about 27% lower, because the ferrite is partly saturated. Ripple calculations belong on the 180 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 65 A, is the peak the part takes at the quoted roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Copper loss at the rated current works out at about 0 mW (- A squared times 0 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Flux swing follows Bp-p = K x L x dI. With K = 330 and a ripple of 19.5 A the core sees roughly 115.8 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    What This Family Is For

    The 11.0 x 8.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 180 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 3 of 4 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 180 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Outline Drawing

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1108R1-R18-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message