Eaton FP1109-R27-R 270 nH 51 A Saturation Inductor
Eaton FP1109-R27-R 270 nH 51 A Saturation Inductor

Eaton FP1109-R27-R 270 nH 51 A Saturation Inductor

Share
pEaton FP1109-R27-R: 270 nH high frequency, high current power inductor, 35 A Irms, 51 A Isat, DCR 0.42 mOhm, 11.0 x 9.0 mm package./p
    • Product Details
    • Download

    FP1109-R27-R at a glance: 270 nH high frequency, high current power inductor, 35 A Irms, 51 A Isat, DCR 0.42 mOhm, 11.0 x 9.0 mm body, 9.0 mm tall.

    Eaton FP1109-R27-R High frequency, high current power inductors

    Eaton builds the FP1109-R27-R as a high frequency, high current power inductor for 11.0 x 9.0 mm footprints. At 270 nH and 35 A Irms with 0.42 mOhm of DCR it targets high-current DC-DC stages; the 9.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Key Specifications

    Orderable part numberFP1109-R27-R
    Inductance, OCL (0 Adc)270 nH
    Inductance, FLL (minimum)160 nH
    Irms (40 °C rise, no core loss)35 A
    Isat (30% roll-off @ +25 °C)51 A
    Isat2 (30% roll-off @ +125 °C)38 A
    DCR typical @ +20 °C0.42 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package11.0 x 9.0 mm, 9.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    At zero bias the winding measures 270 nH. Put Isat1 through it and the figure falls to 160 nH, about 41% lower, because the ferrite is partly saturated. Ripple calculations belong on the 270 nH number; loop stability and worst-case current belong on the lower one.

    The first Isat column, 51 A at +25 °C, is the peak the part takes at 30% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Irms of 35 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.42 mOhm that is roughly 514 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 96.3 mT for a 15.3 A ripple (K = 233). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    What This Family Is For

    The 11.0 x 9.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 270 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 3 of 7 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 270 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.42 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1109-R27-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products