Eaton FP1109-R58-R High Current Inductor, 548 nH 0.42 mOhm
Eaton FP1109-R58-R High Current Inductor, 548 nH 0.42 mOhm

Eaton FP1109-R58-R High Current Inductor, 548 nH 0.42 mOhm

Share
pEaton FP1109-R58-R: 548 nH high frequency, high current power inductor, 35 A Irms, 22.5 A Isat, DCR 0.42 mOhm, 11.0 x 9.0 mm package./p
    • Product Details
    • Download

    FP1109-R58-R at a glance: 548 nH high frequency, high current power inductor, 35 A Irms, 22.5 A Isat, DCR 0.42 mOhm, 11.0 x 9.0 mm body, 9.0 mm tall.

    Eaton FP1109-R58-R High frequency, high current power inductors

    The FP1109-R58-R is a 11.0 x 9.0 mm high frequency, high current power inductor from Eaton, rated 35 A Irms at 548 nH and 0.42 mOhm typical DCR. It is a surface-mount part 9.0 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Electrical Specifications

    Orderable part numberFP1109-R58-R
    Inductance, OCL (0 Adc)548 nH
    Inductance, FLL (minimum)325 nH
    Irms (40 °C rise, no core loss)35 A
    Isat (30% roll-off @ +25 °C)22.5 A
    Isat2 (30% roll-off @ +125 °C)17 A
    DCR typical @ +20 °C0.42 mOhm
    K-factor (Bp-p = K x L x dI)233
    Package11.0 x 9.0 mm, 9.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    548 nH open-circuit, 325 nH at full load: that is a 41% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 30% roll-off at 22.5 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Copper loss at the rated current works out at about 514 mW (35 A squared times 0.42 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    Core loss needs flux, and flux here is about 86.2 mT for a 6.75 A ripple (K = 233). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 11.0 x 9.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 548 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 6 of 7 when the data sheet is sorted by inductance.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 548 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.42 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1109-R58-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message