Eaton FP1109B1-R300-R - 300 nH Shielded Power Inductor 11.0 x 8.2 mm
Eaton FP1109B1-R300-R - 300 nH Shielded Power Inductor 11.0 x 8.2 mm

Eaton FP1109B1-R300-R - 300 nH Shielded Power Inductor 11.0 x 8.2 mm

Share
pEaton FP1109B1-R300-R: 300 nH high frequency, high current power inductor, 55 A Irms, 38 A Isat, DCR 0.19 mOhm, 11.0 x 8.2 mm package./p
    • Product Details
    • Download

    FP1109B1-R300-R at a glance: 300 nH high frequency, high current power inductor, 55 A Irms, 38 A Isat, DCR 0.19 mOhm, 11.0 x 8.2 mm body, 9.0 mm tall.

    Eaton FP1109B1-R300-R High frequency, high current power inductors

    Eaton builds the FP1109B1-R300-R as a high frequency, high current power inductor for 11.0 x 8.2 mm footprints. At 300 nH and 55 A Irms with 0.19 mOhm of DCR it targets high-current DC-DC stages; the 9.0 mm tall body keeps the height budget in check, and the part is rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP1109B1-R300-R
    Inductance, OCL (0 Adc)300 nH
    Inductance, FLL (minimum)216 nH
    Irms (40 °C rise, no core loss)55 A
    Isat (20% roll-off @ +25 °C)38 A
    Isat2 (20% roll-off @ +125 °C)30 A
    DCR typical @ +20 °C0.19 mOhm
    K-factor (Bp-p = K x L x dI)339
    Package11.0 x 8.2 mm, 9.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    At zero bias the winding measures 300 nH. Put Isat1 through it and the figure falls to 216 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 300 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 38 A at +25 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 55 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.19 mOhm that is roughly 575 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 339 turns ripple into flux: a peak-to-peak swing of 11.4 A gives about 115.9 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Where This Part Sits in the Range

    The 11.0 x 8.2 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 300 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it the highest inductance of the 4 parts in this data sheet.

    • Application fit: Compatible with Infineon® DrBlade™ digital voltage regulator controller, Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs).
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    Size the inductor on peak current first, not average. With 300 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.19 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1109B1-R300-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    What does the R suffix on the part number mean?
    It marks RoHS compliance and is part of the orderable number. The characters before it identify body size, version (DCR bin) and inductance in nanohenries: for example FP1007R1-R12-R is the 10 x 7 mm body, R1 version, 120 nH.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products