Eaton FP1110V1-R15-R High Current Inductor, 150 nH 0.23 mOhm
Eaton FP1110V1-R15-R High Current Inductor, 150 nH 0.23 mOhm

Eaton FP1110V1-R15-R High Current Inductor, 150 nH 0.23 mOhm

Share
pEaton FP1110V1-R15-R: 150 nH high frequency, high current power inductor, 61 A Irms, 90 A Isat, DCR 0.23 mOhm, 11.0 x 10.0 mm package./p
    • Product Details
    • Download

    FP1110V1-R15-R at a glance: 150 nH high frequency, high current power inductor, 61 A Irms, 90 A Isat, DCR 0.23 mOhm, 11.0 x 10.0 mm body, 9.5 mm tall.

    Eaton FP1110V1-R15-R High frequency, high current power inductors

    FP1110V1-R15-R is one of Eaton's high frequency, high current power inductor series, 11.0 x 10.0 mm with a 9.5 mm tall profile. Electrically it offers 150 nH at 61 A Irms and 0.23 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Electrical Specifications

    Orderable part numberFP1110V1-R15-R
    Inductance, OCL (0 Adc)150 nH
    Inductance, FLL (minimum)108 nH
    Irms (40 °C rise, no core loss)61 A
    Isat (20% roll-off @ +100 °C)90 A
    Isat2 (20% roll-off @ +100 °C)72 A
    DCR typical @ +20 °C0.23 mOhm
    K-factor (Bp-p = K x L x dI)278
    Package11.0 x 10.0 mm, 9.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Two inductance figures are published. 150 nH is measured with no DC in the winding, 108 nH with the winding loaded to Isat1. The gap between them is 28%, and it is the reason a converter that looks well damped at no load can ring at full current.

    The first Isat column, 90 A at +100 °C, is the peak the part takes at 20% roll-off. Note the temperature: run the same part in a hot enclosure and the usable peak drops, which is why the data sheet prints more than one column.

    Irms of 61 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.23 mOhm that is roughly 856 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 112.6 mT for a 27 A ripple (K = 278). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 11.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 150 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it the lowest inductance of the 11 parts in this data sheet, with the highest DCR in the series at 0.23 mOhm, which is what the extra turns cost.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 150 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    On the board, place the part so the switch-node copper is short and wide. At 0.23 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1110V1-R15-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products