Eaton FP1110V1-R20-R 61 A SMD Power Inductor, 195 nH
Eaton FP1110V1-R20-R 61 A SMD Power Inductor, 195 nH

Eaton FP1110V1-R20-R 61 A SMD Power Inductor, 195 nH

Share
pEaton FP1110V1-R20-R: 195 nH high frequency, high current power inductor, 61 A Irms, 70 A Isat, DCR 0.23 mOhm, 11.0 x 10.0 mm package./p
    • Product Details
    • Download

    FP1110V1-R20-R at a glance: 195 nH high frequency, high current power inductor, 61 A Irms, 70 A Isat, DCR 0.23 mOhm, 11.0 x 10.0 mm body, 9.5 mm tall.

    Eaton FP1110V1-R20-R High frequency, high current power inductors

    FP1110V1-R20-R is one of Eaton's high frequency, high current power inductor series, 11.0 x 10.0 mm with a 9.5 mm tall profile. Electrically it offers 195 nH at 61 A Irms and 0.23 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Key Specifications

    Orderable part numberFP1110V1-R20-R
    Inductance, OCL (0 Adc)195 nH
    Inductance, FLL (minimum)140 nH
    Irms (40 °C rise, no core loss)61 A
    Isat (20% roll-off @ +100 °C)70 A
    Isat2 (20% roll-off @ +100 °C)58 A
    DCR typical @ +20 °C0.23 mOhm
    K-factor (Bp-p = K x L x dI)278
    Package11.0 x 10.0 mm, 9.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 195 nH. Put Isat1 through it and the figure falls to 140 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 195 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 70 A at +100 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 61 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.23 mOhm that is roughly 856 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    The K-factor of 278 turns ripple into flux: a peak-to-peak swing of 21 A gives about 113.8 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    What This Family Is For

    The 11.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 195 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 4 of 11 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.23 mOhm, which is what the extra turns cost.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Design Notes

    The order of checks that works: compute ripple from 195 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    On the board, place the part so the switch-node copper is short and wide. At 0.23 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1110V1-R20-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products