Eaton FP1110V1-R32-R - 320 nH Shielded Power Inductor 11.0 x 10.0 mm
Eaton FP1110V1-R32-R - 320 nH Shielded Power Inductor 11.0 x 10.0 mm

Eaton FP1110V1-R32-R - 320 nH Shielded Power Inductor 11.0 x 10.0 mm

Share
pEaton FP1110V1-R32-R: 320 nH high frequency, high current power inductor, 61 A Irms, 42 A Isat, DCR 0.23 mOhm, 11.0 x 10.0 mm package./p
    • Product Details
    • Download

    FP1110V1-R32-R at a glance: 320 nH high frequency, high current power inductor, 61 A Irms, 42 A Isat, DCR 0.23 mOhm, 11.0 x 10.0 mm body, 9.5 mm tall.

    Eaton FP1110V1-R32-R High frequency, high current power inductors

    Eaton FP1110V1-R32-R is a high frequency, high current power inductor in a 11.0 x 10.0 mm surface-mount package. It carries 320 nH of open-circuit inductance with 61 A Irms and a typical DCR of 0.23 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 9.5 mm tall and rated from -40 °C to +125 °C.

    Electrical Specifications

    Orderable part numberFP1110V1-R32-R
    Inductance, OCL (0 Adc)320 nH
    Inductance, FLL (minimum)230 nH
    Irms (40 °C rise, no core loss)61 A
    Isat (20% roll-off @ +100 °C)42 A
    Isat2 (20% roll-off @ +100 °C)34 A
    DCR typical @ +20 °C0.23 mOhm
    K-factor (Bp-p = K x L x dI)278
    Package11.0 x 10.0 mm, 9.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    320 nH open-circuit, 230 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 42 A at +100 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 61 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.23 mOhm that is roughly 856 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 112.1 mT for a 12.6 A ripple (K = 278). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Positioning in the FP Range

    The 11.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 320 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it part 10 of 11 when the data sheet is sorted by inductance, with the highest DCR in the series at 0.23 mOhm, which is what the extra turns cost.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Putting It to Work

    Start from ripple: dI = (Vin - Vout) x D / (L x fsw). With 320 nH and your switching frequency that gives peak current, and the peak is what has to stay under the Isat column for the temperature inside the enclosure. Then check the DC term against Irms.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.23 mOhm the winding is not the loss, the trace can be.

    Mechanical Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1110V1-R32-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products