Eaton FP1110V2-R180-R 61 A SMD Power Inductor, 180 nH
Eaton FP1110V2-R180-R 61 A SMD Power Inductor, 180 nH

Eaton FP1110V2-R180-R 61 A SMD Power Inductor, 180 nH

Share
pEaton FP1110V2-R180-R: 180 nH high frequency, high current power inductor, 61 A Irms, 72 A Isat, DCR 0.18 mOhm, 11.0 x 10.0 mm package./p
    • Product Details
    • Download

    FP1110V2-R180-R at a glance: 180 nH high frequency, high current power inductor, 61 A Irms, 72 A Isat, DCR 0.18 mOhm, 11.0 x 10.0 mm body, 9.5 mm tall.

    Eaton FP1110V2-R180-R High frequency, high current power inductors

    The FP1110V2-R180-R is a 11.0 x 10.0 mm high frequency, high current power inductor from Eaton, rated 61 A Irms at 180 nH and 0.18 mOhm typical DCR. It is a surface-mount part 9.5 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.

    Specification Table

    Orderable part numberFP1110V2-R180-R
    Inductance, OCL (0 Adc)180 nH
    Inductance, FLL (minimum)130 nH
    Irms (40 °C rise, no core loss)61 A
    Isat (20% roll-off @ +100 °C)72 A
    Isat2 (20% roll-off @ +100 °C)57.5 A
    DCR typical @ +20 °C0.18 mOhm
    K-factor (Bp-p = K x L x dI)328
    Package11.0 x 10.0 mm, 9.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    At zero bias the winding measures 180 nH. Put Isat1 through it and the figure falls to 130 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 180 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 72 A at +100 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Copper loss at the rated current works out at about 670 mW (61 A squared times 0.18 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.

    The K-factor of 328 turns ripple into flux: a peak-to-peak swing of 21.6 A gives about 127.5 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.

    Positioning in the FP Range

    The 11.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 180 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 3 of 11 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.18 mOhm.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    Size the inductor on peak current first, not average. With 180 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.

    On the board, place the part so the switch-node copper is short and wide. At 0.18 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.

    Mechanical Dimensions and Pad Layout

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1110V2-R180-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Is this part AEC-Q200 qualified?
    No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products