
FP1110V2-R200-R at a glance: 200 nH high frequency, high current power inductor, 61 A Irms, 65 A Isat, DCR 0.18 mOhm, 11.0 x 10.0 mm body, 9.5 mm tall.
The FP1110V2-R200-R is a 11.0 x 10.0 mm high frequency, high current power inductor from Eaton, rated 61 A Irms at 200 nH and 0.18 mOhm typical DCR. It is a surface-mount part 9.5 mm tall, operating from -40 °C to +125 °C, and it is built for the phase node of a buck regulator where the inductor sets ripple and the control loop sets the rest.
| Orderable part number | FP1110V2-R200-R |
| Inductance, OCL (0 Adc) | 200 nH |
| Inductance, FLL (minimum) | 144 nH |
| Irms (40 °C rise, no core loss) | 61 A |
| Isat (20% roll-off @ +100 °C) | 65 A |
| Isat2 (20% roll-off @ +100 °C) | 52 A |
| DCR typical @ +20 °C | 0.18 mOhm |
| K-factor (Bp-p = K x L x dI) | 328 |
| Package | 11.0 x 10.0 mm, 9.5 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 200 nH. Put Isat1 through it and the figure falls to 144 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 200 nH number; loop stability and worst-case current belong on the lower one.
Saturation is quoted as 20% roll-off at 65 A at +100 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.
Copper loss at the rated current works out at about 670 mW (61 A squared times 0.18 mOhm). That is the term the Irms rating measures. The missing term is core loss, and at a few hundred kilohertz it can be the larger of the two.
Core loss needs flux, and flux here is about 127.9 mT for a 19.5 A ripple (K = 328). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.
The 11.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 200 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.
That makes it part 5 of 11 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.18 mOhm.
The order of checks that works: compute ripple from 200 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.
On the board, place the part so the switch-node copper is short and wide. At 0.18 of DCR the component is not the resistive bottleneck; the trace and the vias usually are. Thermal vias under the body help more than a bigger copper pour further away.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

How is the part packed?
Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.
Is this part AEC-Q200 qualified?
No. The FP, FPT and FPV families are commercial-grade parts rated for the operating temperature range in the table. For automotive work Eaton uses the EXLA and DRA families, which carry AEC-Q200 qualification and a wider temperature range.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd