Eaton FP1110V2-R220-R 220 nH Power Inductor, 61 A
Eaton FP1110V2-R220-R 220 nH Power Inductor, 61 A

Eaton FP1110V2-R220-R 220 nH Power Inductor, 61 A

Share
pEaton FP1110V2-R220-R: 220 nH high frequency, high current power inductor, 61 A Irms, 59 A Isat, DCR 0.18 mOhm, 11.0 x 10.0 mm package./p
    • Product Details
    • Download

    FP1110V2-R220-R at a glance: 220 nH high frequency, high current power inductor, 61 A Irms, 59 A Isat, DCR 0.18 mOhm, 11.0 x 10.0 mm body, 9.5 mm tall.

    Eaton FP1110V2-R220-R High frequency, high current power inductors

    FP1110V2-R220-R is one of Eaton's high frequency, high current power inductor series, 11.0 x 10.0 mm with a 9.5 mm tall profile. Electrically it offers 220 nH at 61 A Irms and 0.18 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.

    Ratings at a Glance

    Orderable part numberFP1110V2-R220-R
    Inductance, OCL (0 Adc)220 nH
    Inductance, FLL (minimum)159 nH
    Irms (40 °C rise, no core loss)61 A
    Isat (20% roll-off @ +100 °C)59 A
    Isat2 (20% roll-off @ +100 °C)47 A
    DCR typical @ +20 °C0.18 mOhm
    K-factor (Bp-p = K x L x dI)328
    Package11.0 x 10.0 mm, 9.5 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    Moisture sensitivity levelMSL 1
    RoHSCompliant (-R suffix)

    The Figures Explained

    At zero bias the winding measures 220 nH. Put Isat1 through it and the figure falls to 159 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 220 nH number; loop stability and worst-case current belong on the lower one.

    Peak current at 20% roll-off is 59 A at +100 °C. If your ripple is large the peak can sit well above the DC operating point, so check the sum of DC plus half the ripple, not the DC figure on its own.

    Irms of 61 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.18 mOhm that is roughly 670 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Flux swing follows Bp-p = K x L x dI. With K = 328 and a ripple of 17.7 A the core sees roughly 127.7 mT, which is the number to put into the core-loss curve before you trust a 40 °C rise estimate.

    What This Family Is For

    The 11.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 220 nH this is mid-range for the body: moderate ripple, DCR still low, and comfortable operation across most of the switching-frequency range the data sheet quotes.

    That makes it part 6 of 11 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.18 mOhm.

    • Application fit: Multi-phase and Vcore regulators, Voltage Regulator Modules (VRMs), Server and desktop.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing and Layout Notes

    The order of checks that works: compute ripple from 220 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.18 mOhm the winding is not the loss, the trace can be.

    Dimensions and Pad Layout

    The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

    Eaton FP1110V2-R220-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Why is the saturation current listed at several temperatures?
    Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.

    Why does DCR have both a typical and a maximum figure?
    The typical value is what the winding measures in production, the maximum is the limit the part is guaranteed to stay under. Size conduction loss on the maximum, because that is the worst case across a production run and over temperature.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message