
FP1110V2-R320-R at a glance: 320 nH high frequency, high current power inductor, 61 A Irms, 40.5 A Isat, DCR 0.18 mOhm, 11.0 x 10.0 mm body, 9.5 mm tall.
FP1110V2-R320-R is one of Eaton's high frequency, high current power inductor series, 11.0 x 10.0 mm with a 9.5 mm tall profile. Electrically it offers 320 nH at 61 A Irms and 0.18 mOhm typical DCR, which is the combination you want when the rail carries tens of amps and the board has no room for a larger can.
| Orderable part number | FP1110V2-R320-R |
| Inductance, OCL (0 Adc) | 320 nH |
| Inductance, FLL (minimum) | 230 nH |
| Irms (40 °C rise, no core loss) | 61 A |
| Isat (20% roll-off @ +100 °C) | 40.5 A |
| Isat2 (20% roll-off @ +100 °C) | 32.5 A |
| DCR typical @ +20 °C | 0.18 mOhm |
| K-factor (Bp-p = K x L x dI) | 328 |
| Package | 11.0 x 10.0 mm, 9.5 mm height |
| Core material | Ferrite, magnetically shielded |
| Operating temperature | -40 °C to +125 °C (ambient plus self-temperature rise) |
| Moisture sensitivity level | MSL 1 |
| RoHS | Compliant (-R suffix) |
At zero bias the winding measures 320 nH. Put Isat1 through it and the figure falls to 230 nH, about 28% lower, because the ferrite is partly saturated. Ripple calculations belong on the 320 nH number; loop stability and worst-case current belong on the lower one.
Saturation is quoted as 20% roll-off at 40.5 A at +100 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.
Irms of 61 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.18 mOhm that is roughly 670 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.
The K-factor of 328 turns ripple into flux: a peak-to-peak swing of 12.2 A gives about 127.5 mT peak in the core. Read the material loss curve at that flux and your switching frequency to get the loss term Irms leaves out.
The 11.0 x 10.0 mm body sits in the middle of the FP range: wide enough for a winding with low DCR, compact enough to place next to the switching stage without a long loop back to the input capacitors. At 320 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.
That makes it part 10 of 11 when the data sheet is sorted by inductance, and it shares the lowest DCR here at 0.18 mOhm.
Size the inductor on peak current first, not average. With 320 nH the ripple can be a large fraction of the DC term at low inductance, so the peak may be well above the load current - and saturation cares about the peak.
Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.18 mOhm the winding is not the loss, the trace can be.
The drawing below is taken from the Eaton data sheet for this series: body outline, recommended pad layout and winding schematic. Pad geometry matters more than usual here, because the terminals are large and the body sits low, so an undersized pad wicks solder and lifts the part off the plane.

Why is the saturation current listed at several temperatures?
Because the ferrite loses permeability as it heats, so the same winding saturates at a lower current when it is hot. The columns let you read the value at the temperature your board actually runs at instead of scaling a room-temperature number by guesswork.
Can I substitute a lower inductance in the same body?
Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.
Shenzhen Gaorunxin Technology Co., Ltd
Shenzhen Gaorunxin Technology Co., Ltd