Eaton FP1206R1-R40-R High Current Inductor, 400 nH 0.43 mOhm
Eaton FP1206R1-R40-R High Current Inductor, 400 nH 0.43 mOhm

Eaton FP1206R1-R40-R High Current Inductor, 400 nH 0.43 mOhm

Share
pEaton FP1206R1-R40-R: 400 nH high frequency, high current power inductor, 50 A Irms, 24 A Isat, DCR 0.43 mOhm, 8.0 x 12.0 mm package./p
    • Product Details
    • Download

    FP1206R1-R40-R at a glance: 400 nH high frequency, high current power inductor, 50 A Irms, 24 A Isat, DCR 0.43 mOhm, 8.0 x 12.0 mm body, 6.0 mm tall.

    Eaton FP1206R1-R40-R High frequency, high current power inductors

    Eaton FP1206R1-R40-R is a high frequency, high current power inductor in a 8.0 x 12.0 mm surface-mount package. It carries 400 nH of open-circuit inductance with 50 A Irms and a typical DCR of 0.43 mOhm, which places it in the switching stage of a multi-phase regulator rather than in bulk energy storage. The body is 6.0 mm tall and rated from -40 °C to +125 °C.

    Ratings at a Glance

    Orderable part numberFP1206R1-R40-R
    Inductance, OCL (0 Adc)400 nH
    Inductance, FLL (minimum)288 nH
    Irms (40 °C rise, no core loss)50 A
    Isat (20% roll-off @ +25 °C)24 A
    Isat2 (20% roll-off @ +125 °C)19 A
    DCR typical @ +20 °C0.43 mOhm
    K-factor (Bp-p = K x L x dI)358
    Package8.0 x 12.0 mm, 6.0 mm height
    Core materialFerrite, magnetically shielded
    Operating temperature-40 °C to +125 °C (ambient plus self-temperature rise)
    RoHSCompliant (-R suffix)

    The Figures Explained

    400 nH open-circuit, 288 nH at full load: that is a 28% roll-off purely from DC bias, before temperature enters the picture. Use the biased figure when you check peak current against saturation, and the unbiased one when you size the ripple.

    Saturation is quoted as 20% roll-off at 24 A at +25 °C. That is a convention rather than a cliff: past it the inductance keeps falling, and how quickly depends on how hard the core is driven. Compare your worst-case peak against this number, not the average current.

    Irms of 50 A is a thermal rating: the current that lifts the part about 40 °C with no core loss counted. Into 0.43 mOhm that is roughly 1075 mW of copper loss, which is where the rise comes from. Add core loss and the usable DC current falls below the tabulated value.

    Core loss needs flux, and flux here is about 103.1 mT for a 7.2 A ripple (K = 358). Double the ripple and the flux roughly doubles, but the loss does not - it climbs faster than linearly, which is why pushing ripple up to save inductance is not free.

    Series Positioning

    At 8.0 x 12.0 mm this is one of the larger FP bodies, aimed at high-current rails where a single phase carries enough current that paralleling smaller parts would cost more board area than it saves. At 400 nH this sits at the high-inductance end of the family. Ripple is small and core loss with it, but there is less headroom before saturation, because saturation current falls as inductance rises in the same can.

    That makes it the highest inductance of the 5 parts in this data sheet.

    • Application fit: Multi-phase and Vcore regulators.
    • Construction: ferrite core, magnetically shielded, surface mount, supplied on tape and reel.
    • Temperature: -40 °C to +125 °C, ambient plus self-temperature rise.

    Sizing It Into a Design

    The order of checks that works: compute ripple from 400 nH and the duty cycle, add half of it to the DC load to get peak, compare that peak with Isat at the real ambient, and only then look at Irms for heating. Doing it the other way round hides saturation problems.

    Two layout points matter with a part this size. Keep the input capacitor loop short, because the switch node is the main source of radiated noise and the inductor will not fix it. And give the pads enough copper: at 0.43 mOhm the winding is not the loss, the trace can be.

    Mechanical Drawing

    Body outline, pad layout and schematic follow. Check the pad drawing against your own footprint library before the first build: these parts are heavy relative to their footprint and the solder joint carries both the current and the mechanical load.

    Eaton FP1206R1-R40-R mechanical dimensions and recommended pad layout

    Dimensions in millimetres, taken from the Eaton technical data sheet for this series. Tolerances and pad geometry are as drawn; verify against your own footprint before the first production build.

    Frequently Asked Questions

    Can I substitute a lower inductance in the same body?
    Only after checking saturation. Lower inductance means higher ripple and a higher peak current for the same DC load. The part with less inductance usually has more saturation headroom, but the ripple penalty is real, so recalculate peak current before substituting.

    How is the part packed?
    Tape and reel, with the reel quantity stated in the packaging section of the data sheet. The parts are polarised by the terminal marking, so check orientation in the reel before setting up the feeder.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products